Flightdeck Solutions Forum Index Flightdeck Solutions
The place to meet and talk with fellow builders
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Added an Ultra wide lens for recording

 
Post new topic   Reply to topic    Flightdeck Solutions Forum Index -> FDS Customer Project Updates
View previous topic :: View next topic  
Author Message
Michael_B767_ATP



Joined: 22 Mar 2015
Posts: 291

PostPosted: Sun Dec 02, 2018 10:16 pm    Post subject: Added an Ultra wide lens for recording Reply with quote

Hi Everyone,

I added an ultra wide lens to my recording setup, what do you think of the view?

Only thing out of the frame now is the Aft. Overhead panel. I started with a new build, first time try. I'll now have to go in and add my edits via Plane Maker.

https://www.youtube.com/watch?v=8GF8UKQmaAQ
Back to top
View user's profile Send private message
787 George



Joined: 01 Oct 2014
Posts: 133
Location: Lubbock TX, USA

PostPosted: Mon Dec 03, 2018 7:21 pm    Post subject: Reply with quote

The new wide-angle lens is nice Mike but for entertainment purposes I think a variety of views makes it more pleasing (multi-camera) but this is just my opinion. The wide gives a great view of pretty much the entire flight deck.

George
_________________
JetMax 737 SKTQ, Overhead, Pedestal. Precision Flight Controls Yoke & Rudder Pedals, Atari800 XL and Commodore 64 Computers
Back to top
View user's profile Send private message
jackpilot
Site Admin


Joined: 25 Apr 2004
Posts: 937
Location: Montreal

PostPosted: Mon Dec 03, 2018 9:18 pm    Post subject: Reply with quote

Like it..
Maybe try to set the camera a bit higher(looking more down ?)
_________________
Jack
Full B737-800 DSTD/Sim-Avionics P3d4
ALL FDS & OEMs (+custom TQ)
Back to top
View user's profile Send private message
Michael_B767_ATP



Joined: 22 Mar 2015
Posts: 291

PostPosted: Sat Dec 08, 2018 4:18 pm    Post subject: Reply with quote

Hi,

Good news. Xplane Beta 7 is working nicely with all my Zibo edits in plane maker.

I also fixed my rudder issue. The rudder would act as though it was on ice, if I just touched it... it would swing full range, it would also stop working at 80 knots while on the ground.

Not sure why this works but this is what I did to fix the rudder. The rudder is plugged into my xplane11 computer and I run the Zibo mod version 3.31.

I went into the SERVER: Sim-A Flight Controls/Flight Control Config 1/ in sub section (Axis Assigned in sysboard controller).

I then went into Sys-board Controller/Control Axis and made sure the rudder had "NO HARDWARE ATTACHED/SHOWN".

The rudder works in XP11 and in Sim-A. It still shows movement on the MFD, it doesn't swing wildly anymore and I have full control while on the ground and YAW DAMPER no longer needs to be off.

Now it's time to get back to the switches.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Flightdeck Solutions Forum Index -> FDS Customer Project Updates All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group